Contact Us Today! | (262) 784-3340

Blackmer Magnes Pump Skid

Here are Blackmer pump skids designed and built by our team for a chemical manufacturing company to pump solvents. The assemblies consist of Blackmer Magnes pumps coupled to Nord Gear reducers and WEG motors. The Nord Gear Reducer (between the WEG Motor and Blackmer Magnes pump) converts the high speed, low torque input from the […]

Read More »

Glycol Batching Skid

Pictured is a skid designed to transfer batches of Glycol off rail cars and into tanker trucks. To achieve this, a Blackmer MS3 Magnes pump was coupled to a Nord gearbox and a WEG 10 HP explosion proof motor. This assembly pumped the Glycol through an Endress Hauser ProMass Coriolis flow meter to totalize the […]

Read More »

Viking Internal Gear Pump Overhaul

A major asphalt paving company needed their Viking KK4124A internal gear pump for pumping hot oil overhauled. The wear was evident on the rotor, shaft and the pump’s mechanical seal was leaking. The seal flush line was also not set at the correct orientation. After modifying the seal flush line, so it was set at […]

Read More »

What is an Internal Gear Pump and How Does it Work?

Commonly used in several industries, including adhesives, petroleum, cleansing/lubricating products, confectionary and more, internal gear pumps are one of the key pieces of industrial equipment in the production line. What is an internal gear pump and how does it work? What roles does it play in industry? The following article explores the intricacies of internal […]

Read More »

Roots Blower Repair

Pictured is a Roots 68-URAI rotary lobe blower for a leading producer of cement and other building materials. The customer brought us several of these units that needed repair, hoping to save money instead of having to buy brand new units. However, the units were in poor condition, with most needing major parts to function, […]

Read More »

Tuthill/Hypro Oil Filter Skid

This oil filter skid was designed for an industrial refrigeration designer/builder contractor. The contractor wanted to be able to filter oil inline on ammonia compressors and ultimately chose a Tuthill L-Series gear pump to side stream the oil. It’s preferred to have a system that side streams the oil, rather than a system with the […]

Read More »

Kerr Pump Repair

An engineered coating manufacturer needed their Kerr 5500 Series Vertical Process Pump repaired. As seen in the pictures below, excessive scale buildup inside and outside of the pump’s wet end caused the pump to seize or completely lock up. The shaft unfortunately needed to be replaced due to wear in critical areas. After replacing the […]

Read More »

Tuthill Liquid Ring Vacuum Pump Repair

A chemical manufacturer’s Kinney (Tuthill) 2-stage liquid ring vacuum pump’s seals were leaking prematurely due to hard water correlated issues at their facility. After exploring some different options with the customer to extend seal life, they opted for us to rebuild the pump to factory specifications. We replaced the wear parts (seals and bearings) and […]

Read More »

Travaini Liquid Ring Pump System Overhaul

A sign and banner manufacturer wanted their Travaini liquid ring vacuum pump system they purchased on Ebay overhauled. The system features a single stage, oil lubricated liquid ring pump that is used to pull vacuum through a router table to secure material for various projects. The number of usage hours on the system had reached […]

Read More »

Split Case Pump Overhaul

Pictured is a Split Case Pump that had obvious past repair issues. The pump was brought to Anderson by a customer that made rolled aluminum products. Among the chief issues, the impeller clearance and shaft sleeves were not set properly, which resulted in severe wear to the entire rotating assembly. As a result, the shaft […]

Read More »

What is the Buying Process When I am Looking for a Pump?

With so many options to choose from in today’s day and age, buying the right pump for your application can initially feel like an overwhelming task. A task that can cost you time and money if not approached correctly. Providing detailed and accurate information is essential to finding the best pump for your application.  That […]

Read More »

Blackmer Gear G1-133 Pump Additions

These Blackmer Gear G1-133 pump assemblies were built for an adhesives manufacturer for processing PVA adhesives (poly vinyl alcohol). They are made of stainless steel and have 4” flanges. An addition we provided was a stainless-steel guard around the stuffing box at the customer’s request for extra protection. We also welded risers on our standard […]

Read More »